Onkyo TX-RZ70 11.2CH AV Receiver - Official Support Thread

[Ying]

Hi, could someone help me explain/understand the following.

I have a Arendal 1723 subwoofer connected to the Txrz70, the subwoofer has an input gain setting (1V output set to +6dB, 2V output set to 0dB, 4V output set to -6dB, or 8V output set to -12dB) depending on the output voltage of the sub out connection.

I read in Gene,s bench test that the Onkyo can go up to 4 volts, but does that also mean the best setting in the sub is the 4 volt input gain? What input gain setting would be best suited for my sub?

 

[ban25]

Hi, could someone help me explain/understand the following.

I have a Arendal 1723 subwoofer connected to the Txrz70, the subwoofer has an input gain setting (1V output set to +6dB, 2V output set to 0dB, 4V output set to -6dB, or 8V output set to -12dB) depending on the output voltage of the sub out connection.

I read in Gene,s bench test that the Onkyo can go up to 4 volts, but does that also mean the best setting in the sub is the 4 volt input gain? What input gain setting would be best suited for my sub?

Set to 0. When you calibrate with Dirac, you'll see how much gain the AVR needs to apply, ideally a low amount.

 

[Ying]

Set to 0. When you calibrate with Dirac, you'll see how much gain the AVR needs to apply, ideally a low amount.

Ok input gain at 0 (2v) thanks, I will try that.

 

[Frankb]

I bought this reciever to replace the yamaha avantage 3040 . i pair it with Vianna accoustics and svs sub. I dont like the sound. it is harsh and cold. no matter what i do in the setup.. The Yamaha aventage is much much better so i have to send it back ,, cant understand the rave about this thing. i reade somewhere in the comments that i am not the only one. And dirac isnt working also. error after error.

 

[gene]

I bought this reciever to replace the yamaha avantage 3040 . i pair it with Vianna accoustics and svs sub. I dont like the sound. it is harsh and cold. no matter what i do in the setup.. The Yamaha aventage is much much better so i have to send it back ,, cant understand the rave about this thing. i reade somewhere in the comments that i am not the only one. And dirac isnt working also. error after error.

Make sure you have the impedance switch set to the high (8 ohm) setting.

• Turn off all room correction and make sure your tone controls are bypassed or flat.
• My bench tests show this to be a class leading AVR and one of my reviewers is currently reviewing it and not complaining about bad sound. But, Dirac is problematic and that's nothing new.

 

[Pace]

I bought this reciever to replace the yamaha avantage 3040 . i pair it with Vianna accoustics and svs sub. I dont like the sound. it is harsh and cold. no matter what i do in the setup.. The Yamaha aventage is much much better so i have to send it back ,, cant understand the rave about this thing. i reade somewhere in the comments that i am not the only one. And dirac isnt working also. error after error.

Have you tried running dirac from a windows computer? The only issue I've had so far is that the newer versions take a very long time to sync the profile to the receiver, but eventually everything is ok.

I would suggest against using AccuEQ if Dirac does not work; IMO AccuEQ has never been all that great.

 

[dlaloum]

Have you tried running dirac from a windows computer? The only issue I've had so far is that the newer versions take a very long time to sync the profile to the receiver, but eventually everything is ok.

I would suggest against using AccuEQ if Dirac does not work; IMO AccuEQ has never been all that great.

With my DRX3.4 I found AccuEQ to be decent but not as good as Dirac....

On the other hand it allowed me to tune levels & distances for all speakers prior to running Dirac, and led I think to a smoother Dirac experience.

My first Dirac setup was using the phone app, and that was quick and painless.

My second and subsequent tries were using the PC app, and although the interface is far richer, and has a heck of a lot more options, it also took a heck of a lot longer, and was more complicated.

No complaints - I am very happy with the results, but if someone is looking for a quick way to get going (and leave to slower more detailed/complicated methods to a weekend when they have the house to themselves!) - then the mobile app and/or AccuEQ are not a bad way to go!

P.S. - on my first attempt, I had no errors... this may have been due to running AccuEQ first, which meant the gain/levels were already set before heading into Dirac.
Later efforts using Dirac PC version, did experience the errors (associated with optimising the gain/levels and ensuring sufficient headroom between signal and noise)

 

[Trebdp83]

If the recently released manual is accurate, the RZ70 has the same shortcomings of other brand AVRs including 40Gbps limited HDMI Input ports around back with a 9Gbps limited HDMI Input port up front. The Zone 2 HDMI Output port is limited to 18Gbps.

The rerouting of DD/DD+/DTHD 5.1 Surround channel info to Surround Back channels when using them and selecting a straight decode as the listening mode continues here as it does in other Onkyo models. This is also the case when playing IMAX Enhanced DTS 5.1 signals with the IMAX DTS listening mode. Though, the latter will not be as commonly encountered as the former.

Like some other new Onkyo models, the RZ70 drops DTS 96/24, DTS-HD HR and DTS-HD MA as listening modes. DTS will be the displayed mode when using a straight decode of DTS 96/24 signals and DTS-HD will be the displayed listening mode when using a straight decode of DTS-HD HR or DTS-HD MA signals.

 

[dlaloum]

If the recently released manual is accurate, the RZ70 has the same shortcomings of other brand AVRs including 40Gbps limited HDMI Input ports around back with a 9Gbps limited HDMI Input port up front. The Zone 2 HDMI Output port is limited to 18Gbps.

I believe the issue was that the available high bandwidth chipsets were 40gbps...

It isn't clear whether 48gbps chipsets are now readily available, or how much work is involved in the design and integration of new HDMI boards... but chances are that this would not be entertained until they are ready for the next generation...

 

[gene]

Our full review of the Onkyo TX-ZR70 has been published:

Onkyo TX-RZ70 11.2CH AV Receiver Review

The Onkyo TX-RZ70 11.2CH AV receiver boasts 140 watts/ch, 8K HDMI inputs, Auro 3D, FREE Dirac Live and the BEST bench test results we’ve seen in its price class. Is this the best AVR at under $3k?

www.audioholics.com