B BDR1783 Audiophyte Mar 13, 2021 5 0 1 43 Mar 14, 2021 #1 I’ve taken the cover off and blew it out thinking it had dust in it. Also while I had it unplugged tried to reset it with nothing hooked up while it starts up fine and after 40 seconds it powers off and back to flashing red light. I bought it used it’s worked fine for months. Thanks for any help
I’ve taken the cover off and blew it out thinking it had dust in it. Also while I had it unplugged tried to reset it with nothing hooked up while it starts up fine and after 40 seconds it powers off and back to flashing red light. I bought it used it’s worked fine for months. Thanks for any help
TLS Guy Audioholic Jedi Oct 30, 2007 27,295 0 113 79 Eagan MN Mar 14, 2021 #2 BDR1783 said: I’ve taken the cover off and blew it out thinking it had dust in it. Also while I had it unplugged tried to reset it with nothing hooked up while it starts up fine and after 40 seconds it powers off and back to flashing red light. I bought it used it’s worked fine for months. Thanks for any help Click to expand... Unfortunately this is probably very bad news. The only think you can do is plug it in and do a hard reset before the flashing light comes on. I will admit that is a long shot, as the probability is the unit has a very serious fault, and needs repair or replacement. Repair tends to be expensive and the unit will have to be sent to an authorized repair center. I trust you have tested the unit unplugged form all other devices, especially the speakers, as this issue is frequently caused by shorts in the speaker leads. It just takes one whisker. Reactions: Pogre
BDR1783 said: I’ve taken the cover off and blew it out thinking it had dust in it. Also while I had it unplugged tried to reset it with nothing hooked up while it starts up fine and after 40 seconds it powers off and back to flashing red light. I bought it used it’s worked fine for months. Thanks for any help Click to expand... Unfortunately this is probably very bad news. The only think you can do is plug it in and do a hard reset before the flashing light comes on. I will admit that is a long shot, as the probability is the unit has a very serious fault, and needs repair or replacement. Repair tends to be expensive and the unit will have to be sent to an authorized repair center. I trust you have tested the unit unplugged form all other devices, especially the speakers, as this issue is frequently caused by shorts in the speaker leads. It just takes one whisker.
B BDR1783 Audiophyte Mar 13, 2021 5 0 1 43 Mar 14, 2021 #3 Yeah I unhooked everything even removed the cover and blew out any dust. Also checked all the speaker connections at the unit and speakers.
Yeah I unhooked everything even removed the cover and blew out any dust. Also checked all the speaker connections at the unit and speakers.
H highfigh Seriously, I have no life. Sep 14, 2008 24,218 0 113 Mar 14, 2021 #4 BDR1783 said: Yeah I unhooked everything even removed the cover and blew out any dust. Also checked all the speaker connections at the unit and speakers. Click to expand... Did you disconnect the speakers before turning it on? If not, do that. If it's in protection due to a speaker load problem, it may come back to life so you can find the cause. I have seen a lot of speaker wire that was chewed by dogs and cats- if you have pets, check that. Also, make sure the wires aren't shorting at the speakers, especially if you have banana plugs.
BDR1783 said: Yeah I unhooked everything even removed the cover and blew out any dust. Also checked all the speaker connections at the unit and speakers. Click to expand... Did you disconnect the speakers before turning it on? If not, do that. If it's in protection due to a speaker load problem, it may come back to life so you can find the cause. I have seen a lot of speaker wire that was chewed by dogs and cats- if you have pets, check that. Also, make sure the wires aren't shorting at the speakers, especially if you have banana plugs.
B BDR1783 Audiophyte Mar 13, 2021 5 0 1 43 Mar 14, 2021 #5 I had it on the lite hen table when I blew it out with air and cut it on with nothing plugged it and still came on for 20-30 seconds and powered off with the red light flashing so I’m afraid it’s something with the unit
I had it on the lite hen table when I blew it out with air and cut it on with nothing plugged it and still came on for 20-30 seconds and powered off with the red light flashing so I’m afraid it’s something with the unit
lovinthehd Audioholic Jedi Sep 11, 2012 44,872 0 113 Oakridge, OR Mar 14, 2021 #6 Might see if you can get the factory reset to run....page 226 of the manual (pdf version).
B BDR1783 Audiophyte Mar 13, 2021 5 0 1 43 Mar 14, 2021 #7 lovinthehd said: Might see if you can get the factory reset to run....page 226 of the manual (pdf version). Click to expand... That’s what I been doing it gets to the 2nd screen for the setup wizard then powers off
lovinthehd said: Might see if you can get the factory reset to run....page 226 of the manual (pdf version). Click to expand... That’s what I been doing it gets to the 2nd screen for the setup wizard then powers off
lovinthehd Audioholic Jedi Sep 11, 2012 44,872 0 113 Oakridge, OR Mar 14, 2021 #8 BDR1783 said: That’s what I been doing it gets to the 2nd screen for the setup wizard then powers off Click to expand... Not much you can do as a consumer other than the resets.....you I assume tried a soft reset as well?
BDR1783 said: That’s what I been doing it gets to the 2nd screen for the setup wizard then powers off Click to expand... Not much you can do as a consumer other than the resets.....you I assume tried a soft reset as well?
B BDR1783 Audiophyte Mar 13, 2021 5 0 1 43 Mar 14, 2021 #9 lovinthehd said: Not much you can do as a consumer other than the resets.....you I assume tried a soft reset as well? Click to expand... Only one I have done is hold power and channel-/+ until I get the initializing notification
lovinthehd said: Not much you can do as a consumer other than the resets.....you I assume tried a soft reset as well? Click to expand... Only one I have done is hold power and channel-/+ until I get the initializing notification
lovinthehd Audioholic Jedi Sep 11, 2012 44,872 0 113 Oakridge, OR Mar 14, 2021 #10 BDR1783 said: Only one I have done is hold power and channel-/+ until I get the initializing notification Click to expand... Soft reset is unplugging it for a while....
BDR1783 said: Only one I have done is hold power and channel-/+ until I get the initializing notification Click to expand... Soft reset is unplugging it for a while....
