Not Cheap Chinese Junk

Swerd

Swerd

Audioholic Warlord
I'm happy to tell you about something that isn't cheaply-made Chinese junk :)! About a year ago, I bought a dehumidifier for my basement, an Aprilaire model E070. I was designed to stand alone (as I use it) or go into the duct work of an HVAC system. And it has adequate capacity for my basement. It works well. So, this is the opposite of my usual RANT – it's a NOT-RANT.

My wife has been bugging me to clean it's air filter. I dreaded that because 1) Removing the filter is probably a nightmare, and 2) Since getting lung cancer, I'm a lot more feeble than I used to be.

I did it the job this morning … easy peasy!

The dehumidifier looks & feels like most American-made products used to be. It might have been made in China, but it was easy to open the filter access panel, pull out the filter, rinse it off, and put it back in.

The screw that held the access panel wasn't impossibly tiny & short, it took either Phillips head or flat blade screwdrivers, and the panel opened without fully removing (and loosing) the screw itself. The filter itself easily slid out because it was sturdily mounted inside an aluminum frame that was held in place with bracket rails, allowing easy slid-in or -out. That frame included a large, easily seen arrow indicating air flow direction.

I have to point all this out only because too often I've encountered things like those that were made so cheap that they easily jammed, failed, or were a nightmare to use. We've all probably run into battery compartments that were difficult to open or close, and were so poorly marked that battery polarity couldn't be easily seen without bright daylight.

I had feared this would be like so many cheap Chinese-made stuff I've encountered before. The maker knew how to make a product that looks like the real thing, but they scrimped way too much on such things as screw sizes or access panels meant for routine maintenance. Those screws are often so tiny that only a 5-year old child could hold them.

Even the power switch was a properly sized rocker switch. It probably won't fail after half a dozen uses.

I may be old, feeble, and have poor vision. But I do remember the days when all things were better designed and built. Doing this simple air filter job today made me feel young again :).
 
Last edited:
davidscott

davidscott

Audioholic Spartan
I'm happy to tell you about something that isn't cheaply-made Chinese junk :)! About a year ago, I bought a dehumidifier for my basement, an Aprilaire model E070. I was designed to stand alone (as I use it) or go into the duct work of an HVAC system. And it has adequate capacity for my basement. It works well. So, this is the opposite of my usual RANT – it's a NOT-RANT.

My wife has been bugging me to clean it's air filter. I dreaded that because 1) Removing the filter is probably a nightmare, and 2) Since getting lung cancer, I'm a lot more feeble than I used to be.

I did it the job this morning … easy peasy!

The dehumidifier looks & feels like most American-made products used to be. It might have been made in China, but it was easy to open the filter access panel, pull out the filter, rinse it off, and put it back in.

The screw that held the access panel wasn't impossibly tiny & short, it took either Phillips head or flat blade screwdrivers, and the panel opened without fully removing (and loosing) the screw itself. The filter itself easily slid out because it was sturdily mounted inside an aluminum frame that was held in place with bracket rails, allowing easy slid-in or -out. That frame included a large, easily seen arrow indicating air flow direction.

I have to point all this out only because too often I've encountered things like those that were made so cheap that they easily jammed, failed, or were a nightmare to use. We've all probably run into battery compartments that were difficult to open or close, and were so poorly marked that battery polarity couldn't be easily seen without bright daylight.

I had feared this would be like so many cheap Chinese-made stuff I've encountered before. The maker knew how to make a product that looks like the real thing, but they scrimped way too much on such things as screw sizes or access panels meant for routine maintenance. Those screws are often so tiny that only a 5-year old child could hold them.

Even the power switch was a properly sized rocker switch. It probably won't fail after half a dozen uses.

I may be old, feeble, and have poor vision. But I do remember the days when all things were better designed and built. Doing this simple air filter job today made me feel young again :).
A feel-good story for us old guys! :)
 
lovinthehd

lovinthehd

Audioholic Jedi
Reminds me some of the Whynter brand (China made) portable air conditioner I got several years back (2017). Didn't expect a lot from it but was one of the few I could find that met my specific needs. It's run like a champ and changing filters is easy (don't even have to kneel). Much better performance than I expected and I've worked it a lot harder than anticipated (due forest fires).
 
Alex2507

Alex2507

Audioholic Slumlord
it reminds me of a certain Reddit sub, but it's mostly filled with stuff that goes under the category of "
they don't make 'em like they used to".
Now I want a chair that costs as much as some cars I've bought. Mostly for the wife as she works from home but my a$$ likes to sit too.

... and a $1500 dehumidifier. No kidding. I'm working on being a cellar dweller again and the Home Cheapo job makes noise that I'm afraid I've gotten use to.

This thread puts me in mind of needing a #14 Vix bit for just one job. I sprang for the Vix brand even though a cheaper Snappy branded #12, which gets used commonly, has lasted longer than I care to recall.

I think this is what they call having champagne taste on a beer budget.
 

Latest posts

newsletter

  • RBHsound.com
  • BlueJeansCable.com
  • SVS Sound Subwoofers
  • Experience the Martin Logan Montis
Top