New DIY MTM Towers designed by Dennis Murphy and Paul Kittinger

KenM10759

KenM10759

Audioholic Samurai
I'm well aware that many magnets are brittle and being a machinist by trade, I'm pretty good at sizing things.

In reading some of the comments/reviews on the product pages and knowing a little about magnet poles, I guess you have to orient them to each other or they could repel. I checked my KEF speakers and it's definitely magnets both sides. The ones on the grills are those weak, soft stick-on type like you see with so many "refrigerator magnet" products. I have no clue what lies beneath the veneer on the speakers. I just wouldn't want anything loose in the speaker cabinet that could rattle when the grills aren't on.
 
highfigh

highfigh

Seriously, I have no life.
I'm well aware that many magnets are brittle and being a machinist by trade, I'm pretty good at sizing things.

In reading some of the comments/reviews on the product pages and knowing a little about magnet poles, I guess you have to orient them to each other or they could repel. I checked my KEF speakers and it's definitely magnets both sides. The ones on the grills are those weak, soft stick-on type like you see with so many "refrigerator magnet" products. I have no clue what lies beneath the veneer on the speakers. I just wouldn't want anything loose in the speaker cabinet that could rattle when the grills aren't on.
Most of the ones I have seen were mounted with epoxy.
 
KenM10759

KenM10759

Audioholic Samurai
The soft magnets on the grills for my KEF speakers are glued or epoxied to the plastic frames. There's 8 of them per grill!

I can't imagine there would be any production time used to orient the "poles" of them, so I'm thinking use the kit's neodymium magnets in the cabinets and some similar soft magnets on whatever grills I make. It's bound to work fine.
 
A

AuralFission

Enthusiast
Ok guys, I finished my build in September of 2016 after starting January 2016. Haven't taken the time to upload, but here it is. I built both the towers and center. I took a lot of pictures, so the pages are kinda data heavy.

The box:
20160125_154002.jpg

The inside of the box:
20160125_154053.jpg
Everything taken out:
20160125_154414.jpg
20160125_154421.jpg

Stuffing and speaker grille cloth:
20160125_154426.jpg
 
A

AuralFission

Enthusiast
Internal Braces:

That oblong looking thing on the left is a circle cutting jib I made. The router bolts to the wide end with the cutting bit going through the hole. There's an adjustable pin that goes into the hole's center. I like it because it's infinitely adjustable.
20160130_151313.jpg


20160202_172204.jpg


20160202_172251.jpg


20160202_172303.jpg

20160202_172315.jpg


For the bottom brace, I drilled holes to accomodate threaded inserts which would screw into the base. I wanted the base to be removal should I ever need to get into the crossover.

20160213_154623.jpg

I made a little jig to help with inserting the threaded inserts:
20160213_154654.jpg

20160213_154743.jpg

And the finished product:
20160213_161028.jpg

Heres the bottom of the base where the screws thread into the bottom brace:
20160213_161037.jpg
 
Last edited:
A

AuralFission

Enthusiast
Construction of the towers:

Cutting the dados into the sides of the towers. I clamped both sides at the same time make sure they would get the same cut. I used the exact brace that would go into the slot to account for variations in thickness. It was a lot of eyeballing and careful clamping to make sure the guide pieces lined up. I don't have a picture of it, but I used a flush trim bit to cut the dados. I cut about 1/8" each pass. I like it tight!

20160119_153937.jpg


20160119_153947.jpg

20160119_170532.jpg


20160118_150208.jpg
 
A

AuralFission

Enthusiast
More tower construction:

All wood is 3/4" Baltic Birch. The good stuff. I measured wrong and cut a dado in the wrong spot. Here's me clamping up the "plug" for the screw up.

20160120_181836.jpg


Nice and tight:
20160121_200740.jpg

20160121_200708.jpg


Rough fit up:
20160120_152651.jpg


20160119_174443.jpg


The bottoms (these will be flushed trimmed later):
20160121_200748.jpg


20160121_200758.jpg
 
Last edited:
A

AuralFission

Enthusiast
Tower glue up:

This was stressful. I had to glue and clamp up all the braces at one time. Worked out though.

20160214_125015.jpg


20160214_125025.jpg


Inside of the bottom. This is where I did the alignment between the bottom brace and the base.
20160215_130732.jpg



All glued up:
20160215_130724.jpg


20160215_130732.jpg


The port section. Rough fit up of the port and speaker terminals:

20160223_185217.jpg
 
A

AuralFission

Enthusiast
Gluing up the Fronts:

20160223_185339.jpg


Cutting the Chamfer:

20160223_185253.jpg


20160227_130842.jpg


View from the Bottom:

20160310_172256.jpg

After Clamp-Up:

20160312_080113.jpg
 
A

AuralFission

Enthusiast
Gluing the Veneer:

What you see is African Sapele:

20160201_180328.jpg


4' x 8' Sheet:
20160201_180444.jpg


Backside of the Veneer Sheet:
20160201_180536.jpg


Glue and Application Method (I stopped using the tray after awhile. It was faster squirting straight from the bottle and saved glue). Just drizzle on the glue to both the venner and the opposing surface and roll flat with the roller. Bring the two pieces together and clamp up. It was hot at the time, so dry time wasn't that long.

20160305_105236.jpg


20160305_105241.jpg


Gluing the Sides:

20160305_105226.jpg


20160305_170310.jpg


I made sure to leave overhang so I could flush trim the veneer later.
20160305_173604.jpg


Taped up the veneer before I flushed trimmed to prevent the router from damaging the surface.
20160312_084157.jpg
 
Last edited:
A

AuralFission

Enthusiast
More Veneer Work:
20160312_165353.jpg

20160410_124115.jpg


20160312_170328.jpg

20160410_124056.jpg


Gluing the Top (I didn't have a long enough piece at the time, so I spliced a smaller piece):

20160310_173702.jpg

20160410_124045.jpg

20160410_124038.jpg
 
A

AuralFission

Enthusiast
Making the Speaker Grilles:

I don't have a lot of pictures of this process, but I basically clamped the front baffle to another piece of wood to get the profile I wanted and used a flush trim router bit to match the profile. I used Super 77 contact adhesive to attach the grille cloth.

20160709_160955.jpg


I inset magnets into the frame:
20160709_160959.jpg


Here's the front baffles with the magnets in place. I used two part epoxy to fill in the holes and sanded flush.
20160428_183231.jpg


20160428_183248.jpg
 
Last edited:
A

AuralFission

Enthusiast
Gluing the Front Baffles/Prepping the Base:

Taped around the veneered portion to keep glue away:


20160613_175828.jpg


Since I like making things harder for myself, I also used threaded inserts to attached the woofers and tweeters to the baffles. Note the holes in the baffle and the tower. I didn't use the supplied wood screws. I like machine screws, it looks better to me.
20160613_181057.jpg


Making the Base:
20160703_131553.jpg



20160703_131606.jpg
 
A

AuralFission

Enthusiast
Prep work for Painting:

20160703_131629.jpg


20160703_131634.jpg


Back of the Speaker:
20160703_131640.jpg


Some the materials I used for prep:


20160419_154824.jpg

20160419_154817.jpg

20160508_153919.jpg
 
A

AuralFission

Enthusiast
Applying the Stain:

I used Watco Danish Oil, Red Mahogany.

20160830_181927.jpg

20160830_181940.jpg



20160830_182007.jpg
20160830_181944.jpg


With the base and grille:
20160909_173654.jpg

20160909_173722.jpg


20160909_173735.jpg
 
newsletter

  • RBHsound.com
  • BlueJeansCable.com
  • SVS Sound Subwoofers
  • Experience the Martin Logan Montis
Top