Search results

If you hooked up your receiver to that outlet, it will quickly become your stove if you turn the volume up high enough and use forks as your speaker loads :D

As I said in my last post, some receivers have amp assignability so you can reroute them to biamp. SPK A/B are the same connection point either in series or parallel to each other from the same channels.

This is bad advice for someone doing home theater, especially if you are using a processor that truncates the LFE channel when setting the crossover below 80Hz. A better solution would be to place 2 small subs in the room and follow our subwoofer placement guidelines. While square rooms aren't...

I've seen the posts from Simple Mind, I mean Simple Theater :rolleyes: Just goes to show you that the people who know the least amount about such topics, are often the most vocal.

Oh my! All you did was Biwire NOT Biamp. Speaker A/B terminals are either wired in series or parallel to the same amp. If you wish to biamp, you must use 4 amps in the receiver, many of which today allow you to reassign to the front channels for biamping.

Back in my college days working at a high end dealer, I can tell you the Mac speakers from yesteryear were very good indeed.

What is even funnier is any cable can pass this test if you terminate it to its characteristic impedance :rolleyes:

What a load of crap and typical attitude of an audio elitist who thinks you require exotic equipment to drive a pair of speakers. If that was the case. then its more an issue with poor speaker design, NOT poor electronics. Rotel makes good amplifiers, certainly good enough to drive a wide...

No a good amp is still a necessity. We don't listen to continuous test tones and its important to realize that. An amp should have plenty of headroom to hit peaks undistorted while at the same time have a low enough output impedance to minimize frequency response variations when driving a...

Their literature is a load of crapola. I suggest reading this excellent article Rod Elliot authored that covers this very topic. Cable Impedance No cable will pass a high frequency squarewave properly unless it is terminated with the correct impedance at both ends, and the 'proof' that...

I was not "offended" but understood.

All; I am currently reviewing a 5CH linear Class G amp and pulled some efficiency #'s for your enjoyment. Class G amps are typically more efficient than a/b. These tests were conducted using regulation from the APC S15. Amps were testing to no more than 0.1% THD + N. Test tone was a...

THX we fixed it.

Um No. Unless the amp itself has a power supply big enough to sink that much power, its not gonna work. Why do you feel you need that much power and why do you think all channels simultaneously will need it? A single 90dB SPL @ 1 watt/meter speaker playing 10 watts will generate 100dB SPL...

When doing power load estimates for home wiring, you DON"T assume all outlets are operating at full capacity just like you don't assume all channels will be driven at full capacity on a multichannel amplifier. My advice is to run a dedicated line or 2 to your home theater equipment, especially...

Theoretically Class A/B amps can be around 50% efficienct but this is usually never the case. Real world efficiencies range between 35-45% so I used a figure in the middle. The more current you pull from these amps (IE. running them in 4 ohms instead of 8, the more inefficient they become)...

I don't know how to make the math any simpler so let me try again: Standard Wall Outlet is: 120V, 15A UL Compliance Receptacle found on most consumer gear: 15A MAX Power Capability: 120 x 15 = 1,800 watts Typical Efficiency of Linear Amp (not factoring in core losses, or PF): 40% MAX...

Wrong again. If the 5805 was rated 170wpc all 10 channels driven, it would try to consume roughly 170*10/.4 = 4,250 watts or pull 35A from 120V line. NOT BLOODY LIKELY :D

For any Star Trek fans suffering withdrawal symptoms from lack of new Trek, I recommend you get your fix here: Star Trek Borg War This was done by one guy on a Star Trek Game engine and with the real voices of a few Trek actor such as Patrick Stewart. Not bad at all!

Yes I believe they made an additional tweak since the first firmware fix for the bass. Let me know the rev# you have and I will compare it to mine.