help with Peavey MMA 8150T & uma 752

[ReyLobo]

hello guys i came here for knowledge
a friend give me this amplifiers for free.
can any one tell me how can i connect this to my current setup to make it work like a power amps.
source:minix neo x8-h plus
receiver:Denon AVR 2700
speakers:JBL Northridge (E90 L,R) (E30 RL,RR) (EC35 center. internal Tweeter die replaced with external Tweeter Pyramid TW28)
Sub woofer: H-100 Premier Acoustic PA-120
power amplifier:hafler 500 for L,R front

i want connect one of this amplifiers to my center channel from the pre-output center of the receiver.
later on i want to upgrade my receiver since this one don't have any pre-output for rear L&R.
or there is any way to jump speaker wires to this amplifiers ?
i have read a little bit of the manuals but i am not sure if this amplifiers is going to work independents channels like stereo for the rear speakers
I use this setup mostly for movies.
any help will be very appreciated thank you

 

[lovinthehd]

Your avr has only pre-outs for the fronts and the sub. Your L/R surrounds should be fine with your avr's amps in any case. You need phoenix connectors for the amps. I made some rca to phoenix connectors for a similar Crest amp I picked up recently. Go to parts-express.com for components to make some or a pre-made like this http://www.parts-express.com/atlas-sound-as2rca-3m-phx-male-rca-to-phoenix-connector-cable-98-ft-(3m)--242-9471

ps How noisy are the amps? Are you sure you need additional power for the fronts?

 

[BoredSysAdmin]

Your current speakers spec'd at 91db and 8ohm. Connect that to Denon 2700 avr and you would get insanely loud without any external amp.

8150 is multichannel distribution amp - you won't need until you decide to do multi-room audio.
752 is integ amp - rated at 75w - less than your denon I believe
Just sell both - and use money towards new speakers.

 

[ReyLobo]

Your avr has only pre-outs for the fronts and the sub. Your L/R surrounds should be fine with your avr's amps in any case. You need phoenix connectors for the amps. I made some rca to phoenix connectors for a similar Crest amp I picked up recently. Go to parts-express.com for components to make some or a pre-made like this http://www.parts-express.com/atlas-sound-as2rca-3m-phx-male-rca-to-phoenix-connector-cable-98-ft-(3m)--242-9471

ps How noisy are the amps? Are you sure you need additional power for the fronts?

i think i'm gonna use the just the 8150T for the center speaker, and the hafler 500 for the front R,L.
i do still need the RCA To Phoenix connector for the 8150T ?
for connecting just the center speaker and the tweeters ?
how will you connect the speaker wires to this amp ?


can the uma 752 be used to work for any 3.5mm audio jack output ? like for PC,cellphones?

 

[lovinthehd]

i think i'm gonna use the just the 8150T for the center speaker, and the hafler 500 for the front R,L.
i do still need the RCA To Phoenix connector for the 8150T ?
for connecting just the center speaker and the tweeters ?
how will you connect the speaker wires to this amp ?


can the uma 752 be used to work for any 3.5mm audio jack output ? like for PC,cellphones?

Amp overkill! Lots of guys do it in any case. I had a Hafler a long time ago....

On first glance thought it was only phoenix inputs like my Crest, but I do see a few rcas now. Have you looked at manuals for either unit? Should address your questions better than my glance at pictures of the backs

 

[ReyLobo]

well i am not really sure how to wire the speakers i don't want to burn my speaker by doing a bad wiring.
i want to connect just the center speaker with 2 tweeters.

 

[lovinthehd]

well i am not really sure how to wire the speakers i don't want to burn my speaker by doing a bad wiring.
i want to connect just the center speaker with 2 tweeters.

Speaker wiring should be relatively simple from amp to speaker, just need some speaker wire....

OTOH connections from your avr/pre-amp/source to amp that's another conversation. Have you looked at the manuals yet?