Search results

I have had this TV for about 5 to 6 years now has been wall mounted in the same spot the entire time, I recently noticed this mark which looks like something hit it but I live alone and I can't figure out what could of hit it. Any chance it could be the fancy cable which does hdmi & power? see...

I am using Dayton binding posts & plate combo links below, do I need to seal around the plate or the back side of the binding posts? If yes is clear silicone the best to use? Dayton Audio BPP-G Premium Binding Pos...

I wanted to see if the Winisd graphs shown below look correct? The blue line is based on WinIsd box volume and the yellow is based on a smaller sized box. Reading on other forums it seems like for this driver a smaller box around 1.8 to 2. cu ft is recommended. I plan to add two 13.5 W7's in...

I currently use the behringer ep2500 to power a diy sub which has a single JL audio 13W1V2-4. I am interested in adding at least 1 or 2 bass shakers to my couch. Would there be any issues if i run the sub off of the right channel and the 1 or 2 bass shakers off of the left channel? I am...

<o:p> </o:p> My setup: Onkyo 709 as my main receiver which powers my center channel, & mids/highs of my polk RTI 12’s. Pre outs of the receiver go to a DCX2496, two of the DCX outputs go to a Marantz SR4001 & another going to behringer ep2500. I wired the qty (3) 7” drivers in the RTI 12’s in...

I am looking to purchase some frames only, I checked out two sites online, and i notice that the dimensions do not take into consideration the thickness of the frame material for example it list Outside dimensions of 48" X 24" X 2" Which is the same size as the material that is suppose to...

I am selling my Polk monitor 70's black, for $220. Condition like new, no visible marks ect...not used very much at all since I currently work full time as well as taking 3 classes per semester working on my masters. I want to sell these locally, since I do not want to deal any shipping...

I could not resist the Fry's deal got a pair of RTI 12's for $600. Do you think the Onkyo 709 is enough to push these things? These things look sick with the grills off

Amazon.com: Behringer DCX2496 Ultradrive Pro Ultra High-Precision Digital 24-Bit/96 Khz Loudspeaker Management System: Musical Instruments

Looking for a new receiver that has the following 1) some kind of airplay so I can play music from Iphone without a physical hook up 2) 5.1 pre-outs Would like to stick to Marantz or Yamaha but will consider others. thanks

I just received the dcx yesterday still sitting in the box since I have no time to mess around with it now. I was wondering if its possible to substitute the passive crossovers in a speaker with the dcx. say for example my fronts are polk monitor 70's could i remove the crossover inside, and use...

I have the above receiver, and I just picked up the behringer dcx2496, for now I will be using it for my sub only, which will be powered using behringer 2500. I wanted to ask what output I should use from the yamaha receiver to connect to the DCX? Ther are the following outputs on the...

I recently picked up the Yamaha RX-V573, so now i have my old receiver (marantz sr4001) sitting in a box wasting space. I also just ordered the Behringer DCX2496, I currently have Polk monitor 70's and matching center channel as well as diy JL13W1 in a ported enclosure powered using behringer...

I am finally ready to purchase the dcx, I looked quickly online and new they go for $350 does this sound correct? Any input on where I should purchase the dcx? Besides cables is there anything else I would need, I will be using it with my Yamaha RX-V573 receiver to feed a behringer ep2500...

I picked up a pack of the above has a total of 7 2" sheets. I would like to make a few 2' X 2' panels for aesthetics purposes only, but wanted to ask how difficult is it to cut this stuff, is it possible to make a clean cut or is it going to be a mess? Thanks

i picked up the above receiver since it was half off at Frys. I have polk 70 monitors and the matching center channel i ran the speaker setup using the mic it came with, the problem is the sound is very low. the volume range goes from -80 to + 15 i first played a BD concert using my PS3 I could...

I am helping a friend of mines parents with getting new speakers. They currently have a HK AVR 500 and some floor standing front speakers. They are looking to get rid of the floor standing ones for smaller ones they don’t want anything on the floor, the wife was pushing for bose but I said...

A buddy of mine has the above receiver, and is trying to figure out if he should get a new one. He has that along with some polk satelite speakers purchased around the same time do you think its time to upgrade the receiver?

I am currently looking at this tv stand Nexera Pinnacle 56" TV Stand | Racks and Stands only thing i worry about is will i need to have doors open when using equipment because of heat it will hold a PS3, Marantz SR4001, and Behringer EP2500 thanks

I was reading through this thread http://forums.audioholics.com/forums/diy-corner-tips-techniques/52319-beat-recession-highly-cost-effective-diy-speaker-build-using-audax-ap170z0.html I noticed you mentioned something about most speakers skimp out on the components used in making the...